Florida Regulations 62-296.513: Surface Coating of Miscellaneous Metal Parts and Products
Current as of: 2024 | Check for updates
|
Other versions
(1) Applicability.
(a) The emission limiting standards set forth in subsection 62-296.513(2), F.A.C., shall apply to surface coating of the following metal parts and products:
1. Large farm machinery, such as harvesting, fertilizing and planting machines, tractors and combines,
2. Small farm machinery, such as lawn and garden tractors, lawn mowers and rototillers,
3. Small appliances, such as fans, mixers, blenders, crock pots, dehumidifiers and vacuum cleaners,
4. Commercial machinery, such as office equipment, computers and auxiliary equipment, typewriters, calculators and vending machines,
5. Industrial machinery, such as pumps, compressors, conveyor components, fans, blowers and transformers,
6. Fabricated metal products, such as metal covered doors, frames, etc.; and,
7. Any other industrial category which coats metal parts or products under the Standard Industrial Classification Code of Major Group 33 (primary metal industries), Major Group 34 (fabricated metal products), Major Group 35 (nonelectric machinery), Major Group 36 (electrical machinery), Major Group 37 (transportation equipment), Major Group 38 (miscellaneous instruments), and Major Group 39 (miscellaneous manufacturing industries). The Standard Industrial Classification Code is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C., 20402, and may be examined at the Department of Environmental Protection, Tallahassee.
(b) The provisions of Fl. Admin. Code R. 62-296.513, shall not apply to the surface coating of the following metal parts and products:
1. Automobiles and light-duty trucks,
2. Metal cans,
3. Flat metal sheets and strips in the form of rolls or coils,
4. Magnet wire for use in electrical machinery,
5. Metal furniture,
6. Large appliances,
7. Exterior of airplanes,
8. Automobile refinishing,
9. Customized top coating of automobiles and trucks if production is less than 35 vehicles per day;
10. Exterior of marine vessels; and,
11. Aerospace parts and products coating operations that are either:
a. Facilities classified as area sources that comply with primer, topcoat, and specialty coating VOC control requirements of 40 C.F.R. part 63, Subpart GG, as adopted and incorporated by reference in Fl. Admin. Code R. 62-204.800; or
b. Facilities classified as major sources that are subject to 40 C.F.R. part 63, Subpart GG, as adopted and incorporated by reference in Fl. Admin. Code R. 62-204.800
(c) The provisions of Fl. Admin. Code R. 62-296.513, apply to the application area(s), flashoff area(s), air and forced air dryer(s), and oven(s) used in the surface coating of the metal parts and products listed in Fl. Admin. Code R. 62-296.513(1)(a) These provisions also apply to prime coat, top coat, and single coat operations. Credit for transfer efficiency above the baseline of 60% for spray coating operations can be granted according to the following formula:
Terms Used In Florida Regulations 62-296.513
- Baseline: Projection of the receipts, outlays, and other budget amounts that would ensue in the future without any change in existing policy. Baseline projections are used to gauge the extent to which proposed legislation, if enacted into law, would alter current spending and revenue levels.
1. Large farm machinery, such as harvesting, fertilizing and planting machines, tractors and combines,
2. Small farm machinery, such as lawn and garden tractors, lawn mowers and rototillers,
3. Small appliances, such as fans, mixers, blenders, crock pots, dehumidifiers and vacuum cleaners,
4. Commercial machinery, such as office equipment, computers and auxiliary equipment, typewriters, calculators and vending machines,
5. Industrial machinery, such as pumps, compressors, conveyor components, fans, blowers and transformers,
6. Fabricated metal products, such as metal covered doors, frames, etc.; and,
7. Any other industrial category which coats metal parts or products under the Standard Industrial Classification Code of Major Group 33 (primary metal industries), Major Group 34 (fabricated metal products), Major Group 35 (nonelectric machinery), Major Group 36 (electrical machinery), Major Group 37 (transportation equipment), Major Group 38 (miscellaneous instruments), and Major Group 39 (miscellaneous manufacturing industries). The Standard Industrial Classification Code is available from the Superintendent of Documents, U.S. Government Printing Office, Washington, D.C., 20402, and may be examined at the Department of Environmental Protection, Tallahassee.
(b) The provisions of Fl. Admin. Code R. 62-296.513, shall not apply to the surface coating of the following metal parts and products:
1. Automobiles and light-duty trucks,
2. Metal cans,
3. Flat metal sheets and strips in the form of rolls or coils,
4. Magnet wire for use in electrical machinery,
5. Metal furniture,
6. Large appliances,
7. Exterior of airplanes,
8. Automobile refinishing,
9. Customized top coating of automobiles and trucks if production is less than 35 vehicles per day;
10. Exterior of marine vessels; and,
11. Aerospace parts and products coating operations that are either:
a. Facilities classified as area sources that comply with primer, topcoat, and specialty coating VOC control requirements of 40 C.F.R. part 63, Subpart GG, as adopted and incorporated by reference in Fl. Admin. Code R. 62-204.800; or
b. Facilities classified as major sources that are subject to 40 C.F.R. part 63, Subpart GG, as adopted and incorporated by reference in Fl. Admin. Code R. 62-204.800
(c) The provisions of Fl. Admin. Code R. 62-296.513, apply to the application area(s), flashoff area(s), air and forced air dryer(s), and oven(s) used in the surface coating of the metal parts and products listed in Fl. Admin. Code R. 62-296.513(1)(a) These provisions also apply to prime coat, top coat, and single coat operations. Credit for transfer efficiency above the baseline of 60% for spray coating operations can be granted according to the following formula: