Iowa Code 355.7 – Plats of survey
Current as of: 2024 | Check for updates
|
Other versions
A plat of survey shall be made, showing information developed by the survey, for each land survey performed for the purpose of correcting boundaries, correcting descriptions of surveyed land, or for the division of land. Each plat of survey shall conform to the following provisions:
1. The original plat drawing shall remain the property of the surveyor.
Terms Used In Iowa Code 355.7
- Division: means dividing a tract or parcel of land into two parcels of land by conveyance or for tax purposes. See Iowa Code 355.1
- following: when used by way of reference to a chapter or other part of a statute mean the next preceding or next following chapter or other part. See Iowa Code 4.1
- Meander line: means a traverse approximately along the margin of a body of water. See Iowa Code 355.1
- Offset line: means a supplementary traverse close to and approximately parallel with an irregular boundary line. See Iowa Code 355.1
- Ordinance: means a city law of a general and permanent nature. See Iowa Code 362.2
- Plat of survey: means a graphical representation of a survey of one or more parcels of land, including a complete and accurate description of each parcel within the plat, prepared by a licensed professional land surveyor. See Iowa Code 355.1
- property: includes personal and real property. See Iowa Code 4.1
- seal: shall include an impression upon the paper alone, or upon wax, a wafer affixed to the paper, or an official stamp of a notarial officer as provided in chapter 9B. See Iowa Code 4.1
- Subdivision: means a tract of land divided into three or more lots. See Iowa Code 355.1
- Surveyor: means a licensed professional land surveyor who engages in the practice of land surveying pursuant to chapter 542B. See Iowa Code 355.1
- United States: includes all the states. See Iowa Code 4.1
2. The size of each plat sheet shall not be less than eight and one-half inches by eleven inches.
3. The scale of the plat drawing shall be clearly stated and graphically illustrated by a bar scale on every plat sheet.
4. An arrow indicating the northern direction shall be shown on each plat sheet.
5. The plat shall show that the survey is tied to a physically monumented land line which is identified by two United States public land survey system corners, or by two physically monumented corners of a recorded subdivision.
6. a. The plat shall show the lengths and bearings of the boundaries of the parcels surveyed. The course of each boundary line shown on the plat may be indicated by a direct bearing reference or by an angle between the boundary line and an intersecting line having a shown bearing, except when the boundary line has an irregular or constantly changing course, as along a body of water, or when a description of the boundary line is better achieved by measurements shown at points or intervals along a meander line or an offset line having a shown course. The bearings shall be referenced to a United States public land survey system land line, or recorded subdivision line. If the boundary lines show bearings, lengths, or locations which vary from those recorded in deeds, abutting plats, or other instruments of record, the following note shall be placed along the lines:
Recorded as (show recorded bearing, length, or location).
b. Bearings and angles shown shall be given to at least the nearest minute of arc.
7. The plat shall show and identify all monuments necessary for the location of the parcel and shall indicate whether the monuments were found or placed.
8. If United States public land survey system corners control the land description, the corners shall be clearly identified on the plat including a description of the monumentation and shall indicate whether the monuments were found or placed.
9. Control monuments shall be adequately described and clearly identified on the plat and noted as found or placed. If additional monuments are to be placed subsequent to the recording of a subdivision as provided in section 355.6, the location of the additional monuments shall be shown on the plat.
10. Distance shall be shown in decimal feet in accordance with the definition of the U. S. survey foot. Distance measurements shall refer to the horizontal plane.
11. Curve data shall be stated in terms of radius, central angle, and length of curve, and as otherwise specified by local ordinance. In all cases, the curve data must be shown for the line affected.
12. The unadjusted error of closure shall not be greater than one in five thousand for an individual parcel.
13. If any part of the surveyed land is bounded by an irregular line, that part shall be enclosed by a meander line or an offset line showing complete data with distances along all lines extending beyond the enclosure to the irregular boundary, and shown with as much certainty as can be determined or as “more or less”, if variable. In all cases, the true boundary shall be clearly indicated on the plat.
14. The plat shall be captioned to show the date of the survey, and shall be accompanied by a description of the parcel.
15. The plat shall contain a statement by a surveyor that the work was done and the plat was prepared by the surveyor or under the surveyor’s direct personal supervision, shall be signed and dated by the surveyor, and shall bear the surveyor’s Iowa license number and legible seal.